MAKE IT EASY!

    

                      

                MANY OF US MAY STRUGGLE IN STITCHING THE CLOTHES / FABRICS BY HAND. SO WE WISH TO HAVE A MINI PORTABLE SEWING MACHINE TO MAKE OUR LIVES SIMPLE AND EASY. THAT'S WHAT I DID!

            I BOUGHT A MINI ELECTRONIC SEWING MACHINE THROUGH WHICH MY JOB HAS BEEN COMPLETETY MADE RELAXED AND UNCOMPLICATED.

            MODEL : YASM - 505A

               

BENEFICIAL FEATURES OF THIS SEWING MACHINE:

1. 12 DIFFERENT TYPES OF STITCHES

2. REGULATOR TO CHOOSE THE STITCH TYPE:

3. REVERSE STITCHING OPTION :

4. BUILT-IN THREAD CUTTER:

5. BULB:

6. MEASURING SCALE:

POINTS FOR PRECAUTION & SAFETY: 

• READ THE GIVEN MANUAL CAREFULLY. ALL THE NECESSARY POINTS WILL BE THERE IN THE MANUAL ITSELF.
• NEVER GO WITH A STITCH WITHOUT A PIECE OF FABRIC. ENSURE THAT THE MACHINE HAS TO WORK WITH FABRIC UNLESS THE NEEDLE BREAKS.
• DO NOT CHANGE THE STITCH TYPE WHILE THE MACHINE RUNS.

HOW TO SEW?

STEP - 1:

            AT THE REAR SIDE OF THE MACHINE, INSERT THE THREAD ROLL INTO THE STAND AND SEAL IT. TAKE SOME AMOUNT OF THREAD FROM THE ROLL BY SIMPLY PULLING FROM IT.

            TAKE SOME AMOUNT OF THREAD FROM THE ROLL BY SIMPLY PULLING FROM IT.

STEP - 2 :

            TAKE THE THREAD TO THE SECOND PART WHERE IT IS MARKED ON THE MACHINE ITSELF. FIRST, INSERT THE THREAD INTO THE HORIZONTAL PART.

        THEN TAKE A SHARP 90 DEGREE TURN TO MEET THE EDGE OF THE SECOND PART.

            FINALLY, TAKE THE THREAD ALONG WITH THE CIRCUMFERENCE OF THE BOTTOM SCREW.

   

STEP - 3:

            GET THE THREAD ALONG THE DIRECTION OF THREAD TENSIONER. 

            AT THE END OF THIS PART, TAKE A CURVACEOUS TURN AND GET THE THREAD UPWARDS. 

STEP - 4 :

            ADJUST THE HAND WHEEL SO THAT THE TAKE UP LEVER MEETS ITS MAXIMUM HEIGHT. THE HAND WHEEL HAS TO ROTATED TOWARDS YOU.

                AFTER BRINGING THE TAKE UP LEVER TO THAT POSITION, INSERT THE THREAD INTO THE SMALL HOLE OF THE TAKE UP LEVER. THEN, TAKE THE THREAD DOWNWARDS.

STEP - 5 :

    

                NEXT WE HAVE REACHED THE NEEDLE PART. THERE IS A CLAMP HOLDING THE NEEDLE. IT HAS A SMALL HOLE THROUGH WHICH INSERT THE THREAD.        

            LIKEWISE, THE NEEDLE ALSO HAS A SMALL HOLE. INSERT THE THREAD INTO THAT HOLE TOO.

            AFTER INSERTING THE THREAD INTO THE NEEDLE, PLACE THE THREAD STRAIGHT.

STEP - 6 :

                NOW, REMOVE THE CASE FROM THE BOTTOM PART. 

                TAKE THE BOBBIN AND PLACE THE BOBBIN INSIDE THE SPACE OF THE BOTTOM PART. BEFORE INSERTING, TAKE SOME AMOUNT OF THREAD.

        NOW, CAREFULLY ROTATE THE HAND WHEEL SO THAT, THE NEEDLE PULLS UP THE THREAD FROM THE BOBBIN. THEN CLOSE THIS PART.

            

        FINALLY, PLACE THE THRAED FROM THE BOBBIN NEAR TO THE PREVIOUS THREAD.

STEP - 7 :

                MAKE SURE THAT THE PRESSER FOOT SHOULD BE DOWNWARDS, SO THAT THE FABRIC CAN BE STITCHED WELL.

PRESSER FOOT LIFTER UP

                                             PRESSER FOOT LIFTER DOWN

PRESSER FOOT DOWN

IMPORTANT FEATURES : 

• WE CAN RUN THIS MACHINE BY MEANS OF AN ADAPTER OR BATTERY. HERE THE LEFT PART IS FOR FOOT PEDAL AND THE RIGHT PART IS FOR DC ADAPTER. [USE ONLY ONE - EITHER BATTERY OR DC ADAPTER]

BATTERY COMPARTMENT

• FOOT PEDAL CAN ALSO BE USED. [MOST OF THE PEOPLE, PREFER FOOT PEDAL TO ON/OFF SWITCH]

• IF YOU FEEL FOOT PEDAL IS INCONVENIENT TO WORK, YOU CAN GO FOR ON/OFF SWITCH. INSERT THE ADAPTER [OR BATTERIES] AND SIMPLY SWITCH TO EITHER LOW OR HIGH ACCORDING TO YOUR SPEED.

                NOW, YOUR MACHINE IS READY TO SEW... ENJOY!